产品展示-苏州迪泰新材料科研有限公司

苏州工业园区翔宇电子有限公司

化学用品一站式服务

化工生产销售

热点词推荐：

产品展示/Product

ABOUT MOUMOU

网站首页 >> 产品展示

产品展示

DEDT 8416瞬干胶

瞬干胶

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT 8416 a low viscosity surface insensitive cyanoacrylateadhesive. Product 8416 is specifically formulated to rapidlybond difficult substrates and to perform in lower humiditysituations. (Mil-A-46050C Type II, Class I).TYPICAL PROPERTIESEster Base ethyl-2-cyanoacrylateAppearance Clear, colourlessFlashpoint >80°CDensity 1,05Shelf Life 12 months, unopenedViscosity (Brookfield) @ 25°C 1300-1500cP(Spindle 1, 20rpm)POLYMER PROPERTIESAppearance Clear, colourlessSoftening Point c. 125°CRefractive Index, nD20 1,45Full Cure Time 24 hoursSolubility DMF, acetonitrile, acetoneCURED SPEED VS. SUBSTRATEBalsa / Balsa <5 secondsRubber / Rubber <5 secondsNitrile / Nitrile <5 secondsNeoprene / Neoprene <5 secondsEPDM / EPDM <5 secondsSteel / Steel 10-20 secondsPVC / PVC 3-10 secondsPolycarbonate / Polycarbonate 10-40 secondsCURED SPEED VS. GAPThe rate of cure will depend on the bondline gap. Thinbondlines result in high cure speeds, increasing the bond gapwill decrease the rate of cure.CURED SPEED VS. ACTIVATORWhere cure speed is unacceptably long due to large gaps,applying activator to the surface will improve cure speed,However, this can reduce ultimate strength of the bond andtherefore testing is recommended to confirm effect.SHEAR STRENGTHGrit Blasted Steel >15 N/mm²Etched Aluminium >11 N/mm²Nitrile Rubber >10 N/mm²Polycarbonate >12 N/mm²ABS 6~18N/mm²PVC 6~18N/mm²DIRECTIONS FOR USEFor best results the surface must be clean and free fromoil ,grease, rust and other contamination. Best results withDEDT adhesive are obtained by using the minimum amount ofadhesive needed to fill the gap between the two matingsurfaces. Apply firm pressure to mated surfaces until adhesivesets.BLOOMING/CHLOROSISVapor generated by uncured liquid adhesive can be depositedon nearby surfaces leaving a white residue. The condition canbe reduced using one or more of the following methods:Clean with DEDT 755.Reduce quantity of the adhesive used.Increase the airflow.Speed the fixture/cure of the adhesive by using an accelerator.PRODUCT STORAGEStore product in the unopened container in a dry location.Optimal storage:2℃ to 8℃. Keep container tightly capped. Ifstored at low temperature, product must be allowed to returnto room temperature before use, This normally takes 8 to12hours.DISCLAIMERThe data contained within this Technical Data Sheet arefurnished for information only and are believed to be reliableat the time of issue. We cannot assume responsibility forresults obtained by others over whose methods we have nocontrol. It is the responsibility of the customer to determinethe products suitability for use. DEDT Limited and itsassociated companies accept no liability arising out of the useof this information or the products described herein.
DEDT 835瞬干胶

瞬干胶

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT 835 a high viscosity low-odour, low-bloom cyanoacrylate adhesive. The product has a rapid cure rate and issuitable for porous substrates or where gap fill may be required.TYPICAL PROPERTIESEster Base Alkoxy-ethyl cyanoacrylateAppearance Clear, colourlessFlashpoint >81°CDensity 1.10Shelf Life 12 months, unopenedViscosity (Brookfield) @ 25°C 850-1250cPs(Spindle 1, 20rpm)POLYMER PROPERTIESAppearance Clear, colourlessSoftening Point c. 100°CRefractive Index, nD20 1,45Full Cure Time 24 hoursSolubility DMF, acetonitrile, acetoneCURED SPEED VS. SUBSTRATEBalsa / Balsa 15- 20 secondsRubber / Rubber <7 secondsNitrile / Nitrile <7 secondsNeoprene / Neoprene <7 secondsEPDM / EPDM <7 secondsSteel / Steel 20-40 secondsPVC / PVC 20-40 secondsPolycarbonate / Polycarbonate 20-50 secondsCURED SPEED VS. GAPThe rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gapwill decrease the rate of cure.CURED SPEED VS. ACTIVATORWhere cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed,However, this can reduce ultimate strength of the bond and therefore testing is recommended to confirm effect.SHEAR STRENGTHGrit Blasted Steel >14 N/mm²Etched Aluminium >10 N/mm²Nitrile Rubber >4 N/mm²Polycarbonate >3 N/mm²Technical Data Sheet835ABS >6N/mm²PVC >2N/mm²DIRECTIONS FOR USEFor best results the surface must be clean and free from oil ,grease, rust and other contamination. Best results withDEDT adhesive are obtained by using the minimum amount of adhesive needed to fill the gap between the twomating surfaces. Apply firm pressure to mated surfaces until adhesive sets.PRODUCT STORAGEStore product in the unopened container in a dry location. Optimal storage:2℃ to 8℃. Keep container tightly capped.If stored at low temperature, product must be allowed to return to room temperature before use, This normally takes 8to12 hours.DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliableat the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have nocontrol. It is the responsibility of the customer to determine the products suitability for use. DEDT Limited and itsassociated companies accept no liability arising out of the use of this information or the products described herein.
DEDT 1770处理剂

处理剂

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT activator 1770 is a single component non CFC solvent base product, formulated toprovide a faster cure on acicdic surfaces and cure excess DEDT cyanoacrylate adhesive outsidethe bond lines. The product is highly flammable.TYPICAL APPLICATIONSDEDT 1770 is used to increase the cure speed of DEDT cyanoacrylate adhesive. It can beeither pre-or post-applied to the bond. It is especially suited for post application on exposedcyanoacrylate adhesive outside of the bond line.POLYMER PROPERTIESSolvent AcetoneChemical Base Organic AcceleratorAppearance Clear to amberSpecific Gravity 0.79Viscosity (at 25°C) (mPa.s) 0.4Flash Point (TCC) °C -17Dry time (at 20°C) seconds <30PRODUCT BENEFITS* Improves the gap filling capability of cyanoacrylate adhesive.* Reduce Fixture time.* Has zero ozone depletion potential.TYPICAL PERFORMANCEFixture time and cure speed achieved as a result of using DEDT 1770 depend on the adhesiveused and substrate bonded.HANDLING PROCEDURESDEDT 1770 is highly flammable.The solvent may effect certain plastics or coatings. It is recommended that the user check allsurfaces for compatibility before use.DIRECTIONS FOR USE1. Apply DEDT cyanoacrylate adhesive to one of the surfaces to be bond and assemble.2. Apply DEDT 1770 over all exposed cyanoacrylate adhesive by spray or by drop. Use oneLaboratory Data SheetA professional adhensive supplier DEDT New materials（HK）CO.,LTDdrop of activator per one drop of exposed adhesive.3. Apply the DEDT cyanoacrylate product immediately after drying but not more than 50seconds thereafter.4. Apply accelerator again if a delay of more than 45 seconds between original activation andadhesive application.PRODUCT STORAGEDEDT 1770 is classified as highly flammable and must be stored in an appropriate manner incompliance with relevant regulations. Do not store combustible materials. Optimal storage: 8℃to 21℃.DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and arebelieved to be reliable at the time of issue. We cannot assume responsibility for results obtainedby others over whose methods we have no control. It is the responsibility of the customer todetermine the products suitability for use. DEDT Limited and its associated companies acceptno liability arising out of the use of this information or the products described herein.
DEDT AC9促进剂

处理剂

市场价:0.00

价格:0.00

一、简介AC49 是一款厌氧胶专用底剂。用于加快厌氧胶的固化速度。二、适用范围粘接表面为不活泼金属、惰性表面或粘接间隙较大或需要快速固化的场合时适用。三、技术参数主要化学成分：酮有效化学成份：铜盐&胺颜色：绿色色透明粘度：极低比重： 0.79干燥时间： 30-70s有效时间： ≤30 天具体的固化速度与所用的厌氧胶的类型及粘接材质均有关系。以上数据均为在25℃/50±5%条件下测得。四、注意事项本品为易燃品，依据当地法律进行储存及运输。与厌氧胶分开储存和运输，以防使厌氧胶固化变质。溶剂对某些塑料基涂层有腐蚀，选用前请先确认对工件无损害。五、一般性常识该产品不能用于纯氧或富氧体系。也不能用来封存氯气等具有强氧化性的物质。不要将取出后的胶液倒回原包装，以防污染原液。工作场所应通风良好，或强制通风。六、包装铝瓶--------------------------------1L七、储存8-28℃下，于阴凉干燥处密闭保存，远离火源，远离厌氧胶。保质期为24 个月。八、使用方法本品为厌氧胶专用底剂：先将本品涂于预接合件表面，晾干后，再在未喷底剂的粘接面涂厌氧胶，快速接合粘接件。
DEDT 1050AB胶

AB胶

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT H-1050 is a toughened , medium high viscosity , rapid curing industrial grade epoxystructural adhesive with excellent strength. Once mixed , the two-component epoxy cures atroom temperature which provides high peel resistance and high shear strength to a wide varietyof materials including plastics , metals , glass and ceramics. It’s high transparency , highpermeability , and rapid curing at lower temperature characteristics , makes it suitable for manybonding applications.PROPERTIES OF UNCURED MATERIALResin HardenerChemical type Epoxy AmineAppearance Clear liquid Slight yellow liquidSpecific Gravity@25℃ 1.17 1.12Viscosity @25℃ , cps 12000+5000cps 12000+5000cpsFlash point(TOC) , ℃ >90℃ >200℃Mix Ratio (R : H) 1 : 1 (by weight)Working life @25℃ 5-8 min.Initial curing time , 5g@25℃ 15 min.PROPERTIES OF CURED MATERIALFully curing time @25℃ 3 days25℃/24hr 80℃/Water absorption rate , ℃/24hr 97℃/1.5hr%2.6 9.06 5.77Thermal degradation temperature , (TGA10°C/min) , °C 332Thermal expansion constant , (110~170°C) , μm/m/°C 210Thermal conductive constant , w/mK 0.3Hardness ASTM D-1706 , Shore D 84H-1050Technical data sheetGlass transition temperature , Tg , ℃ 52Volume resistivity, ASTM D257 5 x 1015Ω.cmSurface resistivity, ASTM D2575 x 1014ΩDielectric constant & loss, 25°C, ASTM D150 ,measured at 100Hz 4.1(loss0.02)Bonding intensity , room temperature 7 days , JIS K6850 , Kg/cm² 207DIRECTION FOR USE1. For best performance surfaces should be clean and free of grease. Removal of surfacecontaminates such as paints , oxide films , oils , dust , mold release agents before bonding.2. Use gloves to minimize skin contact and keep the work environment in an good air flowingstatus.3. Mix thoroughly by weight in the proportions. Mix vigorously approximately 1~3 minutes afteruniform color is obtained. Keep parts from moving during cure. Contact pressure isnecessary.4. Excess uncured adhesive can be cleaned up with ketone type solvents.STORAGEOptimal storage is in a cool , dry location at a temperature between 8°C to 28°C. Shelf life canbe 1 year under 25℃ storage.NOTEThe data contained herein may be reported as a typical value and/or range (based on the mean value ±2standard deviations). Values are based on actual test data and are verified on a periodic basis. The datacontained herein are furnished for information only and are believed to be reliable. We cannot assumeresponsibility for the results obtained by others over whose methods we have no control. We recommend thateach prospective user test his proposed application before repetitive use.
DEDT3215

厌氧胶

市场价:0.00

价格:0.00

<h1>PRODUCT DESCRIPTION</h1>DEDT 3215 is a single component anaerobic threadlocking material, which is develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces. <h5>TYPICAL APPLICATIONS</h5>* Prevents loosening and leakage of threaded fasteners.* Cylinder liner studs.* Air compressor fasteners.* Refrigeration safety valves. <h5>POLYMER PROPERTIES</h5>TypicalValue RangeChemical Type Dimethacrylate esterAppearance Blue liquidSpecific Gravity 1.1Viscosity (at 25°C) (mPa.s) 7000 5000 to 9000Flash Point (TCC) °C >93 <h5>CURE SPEED VS. SUBSTRATE</h5>The rate of cure will depend on substrates involved.Substrate Fixture time/Full cureSteel 30min/24hrsBrass 40min/24hrsZn Dichromate 50min/24hrs<h6>Stainless Steel 60min/24hrs</h6><h6> </h6><h6>CURE SPEED VS. BOND GAP</h6>The rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gap will decrease the rate of cure.<h1> </h1><h1>CURE SPEED VS. ACTIVATOR</h1>Where cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed, But may also impair overall adhesive performance and therefore testing is recommended to confirm effect. <h6>CURE SPEED VS. TEMPERATURE</h6>The rate of cure will depend on the ambient temperature. High temperature tend to increase the speed.TYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts (N.m). TypicalValue RangeBreakaway Torque 31 25~35Prevailing Torque 35 28~40 <h1>GENERAL INFORMATION</h1>This product is not recommended for use in pure oxygen or rich systems and should not be selected as sealant for chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check for compatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect the cure and performance of the adhesive.This product may not be compatible with plastics, (particularly thermoplastic materials where stress cracking of plastic could result). Users are advised to confirm compatibility of the product with such substrates. <h1>DISASSEMBLY AND CLEANUP PRODUCT</h1>To aid in disassembly, DEDT anaerobic compounds can be weakened by heating to at least 260℃. Once disassembled ,cured adhesive can removed with DEDT Gasket Remover1790 by following instructions. A solvent wipe with an organic or petroleum solvent will remove uncured adhesive outside the joint. PRODUCT STORAGE Product should be stored in a cool, dry location in unopened containers at a temperature between c between 46℉ (8℃) to 82℉ (28℃) unless otherwise stated. To prevent contamination of unused product, do not return any material to its original container. DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliable at the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have no control. It is the responsibility of the customer to determine the products suitability for use. DEDT New materials Limited and its associated companies accept no liability arising out of the use of this information or the products described herein.
DEDT3242

厌氧胶

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT 3242 is a single component anaerobic threadlocking material, which is thixotropic and developsmedium strength . The product cures when confined in the absence of air between close fitting metalsurfaces.TYPICAL APPLICATIONS*Prevents loosening and leakage of threaded fasteners.*Pump and motor mounting bolts.*Engine rocker nut*Situations were disassembly with hand tools is required.POLYMER PROPERTIESTypicalValue RangeChemical Type Dimethacrylate esterAppearance Blue liquidSpecific Gravity 1.05Viscosity(at 25°C)(mPa.s) 2000 1200 to 2800Flash Point(TCC) °C >93CURE SPEED VS. SUBSTRATEThe rate of cure will depend on substrates involved.Substrate Fixture time/Full cureSteel 15min/24hrsBrass 20min/24hrsZn Dichromate 30min/24hrsStainless Steel 40min/24hrsCURE SPEED VS. BOND GAPThe rate of cure will depend on the bondine gap. The bondlines result in high cure speeds, increasing thebond gap will decrease the rate of cure.CURE SPEED VS. ACTIVATORWhere cure speed is unacceptably long due to large gaps, applying activator to the surface will improvecure speed, But may also impair overall adhesive performance and therefore testing is recommended toconfirm effect.CURE SPEED VS. TEMPERATUREThe rate of cure will depend on the ambient temperature. High temperature tend to increase the speedTYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts(N/mm²)TypicalValue RangeBreakaway Torque 19 14~25Prevailing Torque 8 4~11GENERAL INFORMATIONThis product is not recommended for use in pure oxygen rich systems and should not be selected as sealantfor chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check forcompatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect thecure and performance of the adhesive.This product may not be compatible with plastics,(particularly thermoplastic materials where stresscracking of plastic could result). Users are advised to confirm compatibility of the product with suchsubstrates.DIRECTIONS FOR USEFor best results, surfaces should be clean and free of grease. 3243 should be applied to the bolt in adequatequantity to fill all engaged threads. 3243 performs best in thin bond gaps, (0.05mm). Very large thread sizesmay create large gaps which will affect cure speed and strength. This product is designed to give controlledfriction, (torque/tension ratio), during assembly. In cnitical tightening applications this ratio should beconfirmed.PRODUCT STORAGEProduct should be stored in a cool, dry location in unopened containers at a temperature between containersat a temperature between 46℉ (8℃)and 82℉ (28℃)unless otherwise stated. To prevent contamination ofunused product, do not return any material to its original container.DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed tobe reliable at the time of issue. We cannot assume responsibility for results obtained by others over whosemethods we have no control. It is the responsibility of the customer to determine the products suitability foruse. DEDT Limited and its associated companies accept no liability arising out of the use of thisinformation or the products described herein.
DEDT3217

厌氧胶

市场价:0.00

价格:0.00

<h1>PRODUCT DESCRIPTION</h1>DEDT 3217 is a single component anaerobic threadlocking material, which is develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces. <h5>TYPICAL APPLICATIONS</h5>* Prevents loosening and leakage of threaded fasteners.* Cylinder liner studs.* Air compressor fasteners.* Refrigeration safety valves. <h5>POLYMER PROPERTIES</h5>TypicalValue RangeChemical Type Dimethacrylate esterAppearance Red liquidSpecific Gravity 1.1Viscosity (at 25°C) (mPa.s) 7000 5000 to 9000Flash Point (TCC) °C >93 <h5>CURE SPEED VS. SUBSTRATE</h5>The rate of cure will depend on substrates involved.Substrate Fixture time/Full cureSteel 30min/24hrsBrass 40min/24hrsZn Dichromate 50min/24hrs<h6>Stainless Steel 60min/24hrs</h6><h6> </h6><h6>CURE SPEED VS. BOND GAP</h6>The rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gap will decrease the rate of cure.<h1> </h1><h1>CURE SPEED VS. ACTIVATOR</h1>Where cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed, But may also impair overall adhesive performance and therefore testing is recommended to confirm effect. <h6>CURE SPEED VS. TEMPERATURE</h6>The rate of cure will depend on the ambient temperature. High temperature tend to increase the speed.TYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts (N.m). TypicalValue RangeBreakaway Torque 31 25~35Prevailing Torque 35 28~40 <h1>GENERAL INFORMATION</h1>This product is not recommended for use in pure oxygen or rich systems and should not be selected as sealant for chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check for compatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect the cure and performance of the adhesive.This product may not be compatible with plastics, (particularly thermoplastic materials where stress cracking of plastic could result). Users are advised to confirm compatibility of the product with such substrates. <h1>DISASSEMBLY AND CLEANUP PRODUCT</h1>To aid in disassembly, DEDT anaerobic compounds can be weakened by heating to at least 260℃. Once disassembled ,cured adhesive can removed with DEDT Gasket Remover1790 by following instructions. A solvent wipe with an organic or petroleum solvent will remove uncured adhesive outside the joint. PRODUCT STORAGE Product should be stored in a cool, dry location in unopened containers at a temperature between c between 46℉ (8℃) to 82℉ (28℃) unless otherwise stated. To prevent contamination of unused product, do not return any material to its original container. DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliable at the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have no control. It is the responsibility of the customer to determine the products suitability for use. DEDT New materials Limited and its associated companies accept no liability arising out of the use of this information or the products described herein.
dedt53106

UV胶

市场价:0.00

价格:0.00

产品简介迪泰53106 是一种单组分，中粘度的胶粘剂，该产品暴露于足够强度的紫外线/或可见光下会快速固化形成透明胶层，且具有厌氧固化及加热固化的特性.典型用途本品主要用于软/硬塑料粘接/邦定上，易维修，不产生应力开裂。本品对多数基材都表现出，良好的粘接特性，尤其适用于金属和塑料等材料粘结迪泰53106 已经通过ROHS 测试。固化前材料性能注意事项本品不宜用于强氧化性物质的密封，本品对紫外线敏感。贮存和使用过程中避光。固化速度取决于灯的强度、光源与胶层的距离、所需固化的深度或胶层间隙，及基材的透光率。建议胶粘剂的固化所需紫外线最小光强为5mW/cm2(在胶层处测定)，要想使暴露的表面干性固化，需要高光强的紫外线 (最小100mW/cm2 )。对温度敏感的基材，固化时应冷却。必要时检查应力开裂的可能性；过量的胶粘剂用有机溶剂除去,粘接件在承受载荷前先冷却。固化后材料性能（金属卤素灯在光强50mW/cm2 下照射，固化10 秒）项目典型值范围化学类型丙烯酸聚胺酯外观透明液体比重25℃ 1.03粘度25℃ cps 6800 6000~8000闪点℃ ≥73物理性能指标断裂拉伸强度， N/mm2 32（PC 与35#钢，0.5mm 间隙）断裂延伸率，% ASTM D882 170（0.5mm 间隙）模量，ASTM D882， N/mm2 700硬度 ( 肖氏 D ) 58折光率，ND 1.49离子含量 ppm 卤素＜120；Ｋ＋20；Ｎａ＋10耐溶剂测试初始强度保有率 %2 小时 24 小时100℃水 100 100水浸 25℃ 100 100乙醇 75% 25℃ 100 ――热老化性能PC/PVC， 75℃ 100PC/PC ， 90℃ 100电性能介电常数和损耗，ASTM D150 常数损耗100Hz 3.866 0.0487技术资料A professional adhensive supplier DEDT NEW MATERIALS（HK）CO.,LTD固化特性/不同灯类型与固化时间的关系不同灯类型固化时表干时间固化深度与光强度的关系，Fushion300 D 型灯贮存条件8~28℃阴凉干燥处原包装内保存，勿将胶液倒回原包装。远离儿童存放！说明以上各种数据仅供参考，对于任何人采用我们无法控制的方法得到的结果，我们恕不负责。迪泰明确声明对任何必然或意外损失包括利润方面的损失都不承担责任。建议用户每次在正式使用前都要根据本文提供的数据先做实验。1kHz 3.271 0.03641MHz 3.068 0.02193体电，ASTM D149，欧姆.cm 1.406× 1014 ―――表面电阻率， ASTM D 149， 1.79× 1015 ―――介电强度，ASTM D257，kV/m 29项目不同的固化时间（S）紫外线强度Mv/cm2 50 100灯管种类主波峰365nm金属卤素灯＜10 ＜3FushionH&V ＜5 ＜3FushionD ＜5 ＜3项目表面脱黏不同时间（S）紫外线强度Mv/cm2 50 100灯管种类主波峰365nm金属卤素灯＜20 ＜8FushionH&V ＜10 ＜5FushionD ＜10 ＜5

共 17 条记录12 下一页> 末页

推荐产品

DEDT 8416瞬干胶
DEDT 835瞬干胶
DEDT 1770处理剂
DEDT AC9促进剂
DEDT 1050AB胶

苏州工业园区翔宇电子有限公司

地址：苏州工业园区科成路2号1幢3楼

电话：0512-67065375

邮件：xy.liu@dedt.com.cn

手机：13815267065