产品展示-苏州迪泰新材料科研有限公司

苏州工业园区翔宇电子有限公司

化学用品一站式服务

化工生产销售

热点词推荐：

产品展示/Product

ABOUT MOUMOU

网站首页 >> 厌氧胶

产品展示

DEDT3215

厌氧胶

市场价:0.00

价格:0.00

<h1>PRODUCT DESCRIPTION</h1>DEDT 3215 is a single component anaerobic threadlocking material, which is develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces. <h5>TYPICAL APPLICATIONS</h5>* Prevents loosening and leakage of threaded fasteners.* Cylinder liner studs.* Air compressor fasteners.* Refrigeration safety valves. <h5>POLYMER PROPERTIES</h5>TypicalValue RangeChemical Type Dimethacrylate esterAppearance Blue liquidSpecific Gravity 1.1Viscosity (at 25°C) (mPa.s) 7000 5000 to 9000Flash Point (TCC) °C >93 <h5>CURE SPEED VS. SUBSTRATE</h5>The rate of cure will depend on substrates involved.Substrate Fixture time/Full cureSteel 30min/24hrsBrass 40min/24hrsZn Dichromate 50min/24hrs<h6>Stainless Steel 60min/24hrs</h6><h6> </h6><h6>CURE SPEED VS. BOND GAP</h6>The rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gap will decrease the rate of cure.<h1> </h1><h1>CURE SPEED VS. ACTIVATOR</h1>Where cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed, But may also impair overall adhesive performance and therefore testing is recommended to confirm effect. <h6>CURE SPEED VS. TEMPERATURE</h6>The rate of cure will depend on the ambient temperature. High temperature tend to increase the speed.TYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts (N.m). TypicalValue RangeBreakaway Torque 31 25~35Prevailing Torque 35 28~40 <h1>GENERAL INFORMATION</h1>This product is not recommended for use in pure oxygen or rich systems and should not be selected as sealant for chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check for compatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect the cure and performance of the adhesive.This product may not be compatible with plastics, (particularly thermoplastic materials where stress cracking of plastic could result). Users are advised to confirm compatibility of the product with such substrates. <h1>DISASSEMBLY AND CLEANUP PRODUCT</h1>To aid in disassembly, DEDT anaerobic compounds can be weakened by heating to at least 260℃. Once disassembled ,cured adhesive can removed with DEDT Gasket Remover1790 by following instructions. A solvent wipe with an organic or petroleum solvent will remove uncured adhesive outside the joint. PRODUCT STORAGE Product should be stored in a cool, dry location in unopened containers at a temperature between c between 46℉ (8℃) to 82℉ (28℃) unless otherwise stated. To prevent contamination of unused product, do not return any material to its original container. DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliable at the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have no control. It is the responsibility of the customer to determine the products suitability for use. DEDT New materials Limited and its associated companies accept no liability arising out of the use of this information or the products described herein.
DEDT3242

厌氧胶

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT 3242 is a single component anaerobic threadlocking material, which is thixotropic and developsmedium strength . The product cures when confined in the absence of air between close fitting metalsurfaces.TYPICAL APPLICATIONS*Prevents loosening and leakage of threaded fasteners.*Pump and motor mounting bolts.*Engine rocker nut*Situations were disassembly with hand tools is required.POLYMER PROPERTIESTypicalValue RangeChemical Type Dimethacrylate esterAppearance Blue liquidSpecific Gravity 1.05Viscosity(at 25°C)(mPa.s) 2000 1200 to 2800Flash Point(TCC) °C >93CURE SPEED VS. SUBSTRATEThe rate of cure will depend on substrates involved.Substrate Fixture time/Full cureSteel 15min/24hrsBrass 20min/24hrsZn Dichromate 30min/24hrsStainless Steel 40min/24hrsCURE SPEED VS. BOND GAPThe rate of cure will depend on the bondine gap. The bondlines result in high cure speeds, increasing thebond gap will decrease the rate of cure.CURE SPEED VS. ACTIVATORWhere cure speed is unacceptably long due to large gaps, applying activator to the surface will improvecure speed, But may also impair overall adhesive performance and therefore testing is recommended toconfirm effect.CURE SPEED VS. TEMPERATUREThe rate of cure will depend on the ambient temperature. High temperature tend to increase the speedTYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts(N/mm²)TypicalValue RangeBreakaway Torque 19 14~25Prevailing Torque 8 4~11GENERAL INFORMATIONThis product is not recommended for use in pure oxygen rich systems and should not be selected as sealantfor chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check forcompatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect thecure and performance of the adhesive.This product may not be compatible with plastics,(particularly thermoplastic materials where stresscracking of plastic could result). Users are advised to confirm compatibility of the product with suchsubstrates.DIRECTIONS FOR USEFor best results, surfaces should be clean and free of grease. 3243 should be applied to the bolt in adequatequantity to fill all engaged threads. 3243 performs best in thin bond gaps, (0.05mm). Very large thread sizesmay create large gaps which will affect cure speed and strength. This product is designed to give controlledfriction, (torque/tension ratio), during assembly. In cnitical tightening applications this ratio should beconfirmed.PRODUCT STORAGEProduct should be stored in a cool, dry location in unopened containers at a temperature between containersat a temperature between 46℉ (8℃)and 82℉ (28℃)unless otherwise stated. To prevent contamination ofunused product, do not return any material to its original container.DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed tobe reliable at the time of issue. We cannot assume responsibility for results obtained by others over whosemethods we have no control. It is the responsibility of the customer to determine the products suitability foruse. DEDT Limited and its associated companies accept no liability arising out of the use of thisinformation or the products described herein.
DEDT3217

厌氧胶

市场价:0.00

价格:0.00

<h1>PRODUCT DESCRIPTION</h1>DEDT 3217 is a single component anaerobic threadlocking material, which is develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces. <h5>TYPICAL APPLICATIONS</h5>* Prevents loosening and leakage of threaded fasteners.* Cylinder liner studs.* Air compressor fasteners.* Refrigeration safety valves. <h5>POLYMER PROPERTIES</h5>TypicalValue RangeChemical Type Dimethacrylate esterAppearance Red liquidSpecific Gravity 1.1Viscosity (at 25°C) (mPa.s) 7000 5000 to 9000Flash Point (TCC) °C >93 <h5>CURE SPEED VS. SUBSTRATE</h5>The rate of cure will depend on substrates involved.Substrate Fixture time/Full cureSteel 30min/24hrsBrass 40min/24hrsZn Dichromate 50min/24hrs<h6>Stainless Steel 60min/24hrs</h6><h6> </h6><h6>CURE SPEED VS. BOND GAP</h6>The rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gap will decrease the rate of cure.<h1> </h1><h1>CURE SPEED VS. ACTIVATOR</h1>Where cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed, But may also impair overall adhesive performance and therefore testing is recommended to confirm effect. <h6>CURE SPEED VS. TEMPERATURE</h6>The rate of cure will depend on the ambient temperature. High temperature tend to increase the speed.TYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts (N.m). TypicalValue RangeBreakaway Torque 31 25~35Prevailing Torque 35 28~40 <h1>GENERAL INFORMATION</h1>This product is not recommended for use in pure oxygen or rich systems and should not be selected as sealant for chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check for compatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect the cure and performance of the adhesive.This product may not be compatible with plastics, (particularly thermoplastic materials where stress cracking of plastic could result). Users are advised to confirm compatibility of the product with such substrates. <h1>DISASSEMBLY AND CLEANUP PRODUCT</h1>To aid in disassembly, DEDT anaerobic compounds can be weakened by heating to at least 260℃. Once disassembled ,cured adhesive can removed with DEDT Gasket Remover1790 by following instructions. A solvent wipe with an organic or petroleum solvent will remove uncured adhesive outside the joint. PRODUCT STORAGE Product should be stored in a cool, dry location in unopened containers at a temperature between c between 46℉ (8℃) to 82℉ (28℃) unless otherwise stated. To prevent contamination of unused product, do not return any material to its original container. DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliable at the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have no control. It is the responsibility of the customer to determine the products suitability for use. DEDT New materials Limited and its associated companies accept no liability arising out of the use of this information or the products described herein.

共 3 条记录1

推荐产品

DEDT 8416瞬干胶
DEDT 835瞬干胶
DEDT 1770处理剂
DEDT AC9促进剂
DEDT 1050AB胶